Quick tip: There's no shame in calling a plumber if you're overwhelmed or need help. Turn your water supply on by turning the handle at the base of the hose back to the left. Reconnect the water supply hose to the bottom of your tank by positioning it and then tightening the lock nut on the end of the hose.Ĩ. The specific installation steps will vary depending on the fill valve model that you buy, so refer to the installation instructions that come with the valve.ħ. The best way to accomplish this is to bring your old fill valve with you to the hardware or plumbing store.Ħ. You'll need to buy a new fill valve that's the same size as your previous valve. You should now be able to remove the fill valve by lifting it straight up.ĥ. Reach down into the tank and locate the lock nut at the base of the fill valve. Unscrew that hose and drop the loose end into a bucket.Ĥ. Follow the water supply hose up to where it connects to the bottom of your tank. Disconnect the water supply from the tank. If your fill valve is leaking, you'll need to replace it following the steps below.ģ. If it's too high or too low, you'll need to repeat the process to make the appropriate adjustment.Ī leaky fill valve could be the cause of a running toilet. Once it's full, make sure that the float is sitting at the water level. After making the adjustment, turn the water to the tank back on by screwing the handle on the water input hose to the left. With the float in the proper position, tighten the clip by either releasing it or rotating it. Adjust the float until it is even with the water line that you identified earlier.Ħ. Lower or raise the float by pushing down on it or pulling up on it. Loosen the clip by either squeezing or rotating it.ĥ. Looking into the tank, you'll see a long tube that runs from the float to the fill valve. If it's too high or too low, you'll need to repeat the process to make the appropriate adjustment.ģ. After making the adjustment, turn the water to the tank back on by turning the handle on the water input hose to the left. You can loosen the screws more to lower the float, or you can tighten them to raise the float.ĥ. Looking at the water line on the tank, determine where the float needs to sit. The screws are often located close to the fill valve.Ĥ. Using a screwdriver, loosen the screws holding the float in place by turning counterclockwise. Turn that handle all the way to the right until it's tight.ģ. That hose goes into your wall or floor, and there will be a handle at the base of the hose. Your toilet's water supply comes through a hose that's often on the left side of the toilet. Make reference of this point so you know where you'll want your float to sit after the adjustment.Ģ. There might be a line on the toilet tank that identifies the ideal water line. It's best to have your float set so it is one to two inches beneath the overflow tube. Adjust the chain so there's about ½-inch of slack when your flush lever is in the normal position.ġ. If it's too short, the flapper may not be able to close and seal properly. If it's too long, the flapper won't fully lift off of the drain hole, so you won't get a full flush. The flapper chain needs to be the right length. The exact installation method you'll use will depend on the type of flapper you have, so refer to the directions that come with your new flapper.Ħ. Most hardware store staff will also be able to help you.ĥ. The easiest way to ensure you're buying the right flapper is to take your old flapper to the hardware store with you so you can compare the models. Your new flapper will need to be the same size and type as your old one. Different flappers mount into the tank in different ways, but you should be able to wiggle, bend, and otherwise remove the flapper from the base of the tank.Ĥ. The flapper will have a chain that attaches to the flush lever inside your tank, which you can unclip. By flushing the toilet, you'll drain all of the remaining water from the tank.ģ. Turn that handle all the way to the right until it's tight.Ģ. If you've determined that the flapper is leaking, then you'll need to replace it. The flapper is at the base of the tank and lets water flow from the tank to the bowl.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |